Відео

Terrifying..........thank you. 😊

where did you find this one? had it long?

You scored a nice rig!! Good for you.

Scanners are my hobby, and ⅔ of the handheld scanners i have aquired that were not working had one thing in common...... battery corrosion. Depending on the location, a tiny spot of corrosion can affect a scanner, so its important to not only remove the corrosion that is readily visable, but àlso the corrosion that is not easy to see. Sometimes when batteries leak off the corrosion will run beyond the battery compartment and into the scanner itself, so if theres a lot of corrosion involved and you've cleaned what you can see and the radio still doesnt come on, remove the screws and carefully open it up to make sure the corrosion hasnt gone beyond the battery compartment. Ive cleaned corrosion inside the case and even on the circuit board. Ive had scanners with tons of corrosion that still worked, and ive had scanners with the smallest amount of corrosion that wouldn't even turn on. Location, location, location.

Don't see the horn .......By the way we have these things called mobile phones now.

Negative image showing the watch back to front, hilarious video quality.

didn't show us how to change the band size by using that tool.

How do ya engage the blades

for the money Cubs are good. I've got an xt1 50 inch cut with 250 hrs on..only issue is I need to install a throttle control lever..mine is sticking but other that that it runs great. Cub push mower is also been a good purchase.

I think your mic gain, should be higher 45-50-55.

How do you remove the front dial knobs in order to take off the front panel. I would also like to know how to remove the switch covers on the levers on the front. I am having a hard time finding any service manuals online. Thanks!

🍿👋

The issue i am having with this is my ac just turns itself on and changes vents and fan controls all on its own. in like a cycle! I can not figure out what is going on or how to fix it. i dont really want to go back to no radio. but i cant deal with heat and ac turning on and off whenever it wants. have you had any of these issues?

this is the mower I got this season

Mine is freezing everything no matter what setting I put it on.

Is the yellow the power wire or is it the blue onw

I always recommend a spare battery for HTs

I guess my air pump for my fish tank doesn't draws enough amps because it won't work like stated I got it awhile back and finally used it and the only ones I can make work are master and the two always on even my pond water pump doesn't seem to trigger it

really cool channel Electro man, subbed and gonna browse more of what you have. Keep posting!

Pretty neat little radio! Is it capable of marine frequencies? I know nothing about radios. Thanks for your review!

Well my new NUC did not see the Acassis via a USB A to USB C cable and I realised that only when tried to copy a picture from my phone!!! 256 GB Drive pretty full was all copied onto target drive and visible in Windows Disk Manager Utility. So now I can try to repair this drive using Win7 repair and have the original as a back up if necessary for a smarter technician then me. LOL.

These were made by a company in China and sold on the US under a bunch of different names - I have the Emerson version with a different signal meter. Not bad with a longwave antenna for AM and shortwave and it has a good sounding speaker. The directional antenna will somewhat help with signal strength but its not sensitive enough for radio direction finding. Air Band is OK but the static between transmissions gets annoying. Id say its good for a kitchen radio or for just playing around. A $5 longwire antenna that plugs into the antenna jack will really make a difference for AM and Shortwave DXing.

I did the same thing today with a return valve. I had a small piece to finish cutting and $&@(/ went sideways. So off I go to get a patch kit. Good thing these pools can stand a few stupid diy mishaps! 😂

2022 cub cadet is piece junk keep throwing belt 5 times now battery dead has 10 hours on meter nothing but trouble

Very helpful! Especially Source and Target drive. Picture in Manual shows the oppossite not referring to A or B just to source and Target which you cannot find written anywhere! And fair enough push power 2nd time to get fan running and cloning a 256 pretty full drive to a 1TB. Start 5.16pm, 25% at 5.17, 50% at 5.17 as well 75% at 5.18 and 100% at 5.18pm. That was fast and all lights simply stay on. Air coming out still cool. So I guess I should dare and switch it off. Well with the ON Button you can now only switch On and Off the fan, but not the unit. So let it run a bit longer and then probably pull the plug on it. Might try holding the ON button down, yep that switches the system off. LOUSY MANUAL! COOL DEVICE.

Is it possible to attach heatsink on it?

Link is broken

4 yrs ago .the watch is still ok?

Not a Galaxy DX II. I HAVE 1, rhis a 2517

How did you fix the 1, 35 metre steel whip at the top? How deep inside? There is no mention in the manual of what to do...maybe for SWR adjustment how?

Great vid. Thanks for the close ups of the procedure. I'm not into modding mine (and the chuffing on the DX-394 doesn't bother me at all), but seeing the inside of the front of the radio was instructive.

Cheap! Not Rolex Look! Should be about $25.

“I’m a grown adult and I’ll never do that” 😂😂😂

Had a similar issue with mine. But it would start having issues until an hour or so of mowing, turns out there where plastic shavings in the tank and they where getting stuck in the 90 of the siphon tube. had to mow until it started starving for gas the pull the tube a blow out the garbage with an air gun.

Said I would update, so here is what fixed mine.😀My solenoid was new, but I checked it, anyway. It was working fine. I had changed all the fuel lines-checked all the clamps ( put worm drive clamps on all hoses)- I didn't forget to tighten any. Started the mower in my shop, and let it run for a while. Yes, I opened all 3 garage doors, the walk thru door, and turned on the exhaust fans. After about 20 minutes, I shut it down. I noticed gas coming out of the gas tank around the seal for the 2 way valve..When I loosened the clamp, gas went everywhere. I put a catch pan under the mower, and pulled the valve. Gas poured out of the hole for about 30 seconds. When I checked the valve, it only worked gas flowing out, but not back into the tank. I took the valve in the house, and cleaned it with Dawn dish soap, as it was dirty. When I forced water through it, a piece of a leaf popped out, and the the valve worked in both directions! Put everything back together, and mowed for 10 hours-we have a tropical storm in the Gulf, and I haven't mowed my 8 acres in 3 weeks! All done, now. I did order a new valve from Ariens, just in case.

Thanks for the video. I just got mine in, same exact one. I like it. It's a heavy watch. Look beautiful and does turn heads.

Geeez. I cannot aee how you are getting that cursed pin in the handke and through the bar!!!!!

Great video Mon Ami ..... Where can I get those parts from ? .... Keep making the 25 and 29 videos , not all repairs are the same .... Xtal leg failures from the board glue is agood example ..... VCO alignment ..... Oh I did find a voltage regulator for my HP 8656B signal generator .... It's a funny thing that it has a 8657 face on it , and green led's , It is one of the later models right before the 8657 came out ....

I have had this watch for a good 10years. However, the world times on my watch are all incorrect and not sure how to fix that.

I've experienced some issues with the fabricated 50" deck bottoming out in the edges on small humps and hills, the workaround being just to raise the deck and then lower it again once you get over the hump. Not a huge deal but so far mine has been pretty great

Have the same problem on my FR691V, thanks for the help.

Good evening. I purchased an Olevs skeleton watch for women, and I am looking for a youtube video to walk me through the setup on this beautiful piece. If you do a video (youtube). It would be very much appreciated. Thanks blessings

Good video! I have an 2007 that needs this done. I may just replace the whole drive shaft like you did. Thanks!

I have this same antenna. I installed it on the roof of my house. I have a hard time hearing anything on 10M. I have not been able to make a single contact on it. The SWR on 10M is flat when tuned. When monitoring 80M and 40M, I can pick up TX every once in a while, but there is a lot of noise. I am a brand new HAM, so I am sure I have something set up wrong. I am beating my head against the wall.

What type of gas you using? Thanks!

Doing all the upgrades I intend to do. I have the hitch ball on the John Deere and used it often around the property. Really helpful videos to guide me in my upgrades.

The first garden tractor we had was a Craftsman GT6000 with the Onan 18HP Twin cylinder horizontal shaft engine, 3 speed spicer transaxle with 2 ranges, and 44" mower deck....that thing mowed our 2 acre property for 21 years before the internal engine components decided to part ways with each other :(. It was replaced with a Craftsman YT4000 lawn tractor...it had the Briggs & Stratton 24HP Twin engine, and 42" mower deck....biggest pile of junk managed to get 7 years out of it before the engine threw a rod. The Cub Cadet XT1 42" with the Kohler 18HP single cylinder engine replaced the YT4000...good lawn tractor, my uncle has it now though, but it seemed to have better power than that YT4000's supposed 24HP engine...I ran the Cub Cadet 44" 3 stage snow blower a few times and it had plenty of power to run it, I had the rear weight bracket and tire chains for it. I had the mulching kit installed on my XT1, it mulched leaves extremely well, I had the Gator G5 mulching blades (not the Cub Cadet blades), plus the mulch plug and it did great, mulched the grass most of the year, except the first few cuttings in the spring when the grass was thick and heavy. It's cut quality was great, and if my uncle didn't need a mower I'd still have it LOL. If I replace my XT1, I may get a zero turn as I have a sub-compact tractor so I just need something to mow with so I don't have to install the 60" mid mount deck on my tractor all the time LOL. A fabricated deck is a good way to go....better built, easy to repair, and lasts a lot longer than those paper thin stamped decks. The fabricated decks are heavier too.

Just bought one yesterday (June 13, 2024) and haven't used mine yet. I am coming from a 13 year old John Deere - 2 decks and plenty of spindle replacements. I passed on the John Deere because my neighbor has new one and always in the shop. Not what they used to be. Anyway, got the cub and in addition to the hour meter missing, I can't understand, at this price point, why they didn't add a front bumper. Anyway, new subscriber and appreciate your videos.

I have the exact same mower however mine has a hour meter!

4:13 golf course? nnnnnnot so much